DIY Shallow Water Anchor Extension Kits (Modular)


Extend your existing DIY Shallow Water Anchor  – just match the fiberglass outer diameter AND color!

These kits are for extending your DIY shallow water anchor setup to allow you to anchor in deeper waters.

These DIY Shallow Water Anchor Extension Kits are for use with the Max-Gain Systems, Inc. DIY Shallow Water Anchor Kits. They are designed to be extensions for modular shallow water anchor systems. The modular extensions include one piece, of the desired outer diameter and color, of fiberglass and one male and one female stainless steel coupler. If you need a full shallow water anchor system, we have full DIY anchor kits available from 8 feet long up to 16 feet long!

We have kits that use these extension kits in them already. These kits may be used to extend your “already modular” shallow water anchor OR extend your existing shallow water anchor.

Example of a DIY Shallow Water Anchor Kit with extensions:

In order to extend your existing shallow water anchor, that is not already modular using our stainless steel couplers, you will need two additional items being one additional male AND one female stainless steel coupling of the correct diameter. Each DIY Shallow Water Anchor Extension Kit includes one piece of fiberglass? and one male and one female coupling. You will need to cut your current anchor, at the location down the shaft, where you want to make it modular. Allowing for use with DIY Shallow Water Anchor Extension Kits AND our incredibly useful DIY Modular 4-IN-1 Paddle Kits. You will need a “fine toothed hacksaw, miter saw with an abrasive cutting wheel, and/or an angle grinder with a metal/masonry cut-off wheel in order to make the perfectly flat cut you will need in order to secure your Stainless Steel Couplers to the rod. Apply your JB Weld (Original Cold Weld Formula, DO NOT use Marine JB Weld) to the outside of the rod in three vertical strips, equidistant around the rod. This will allow you to put the coupler onto the rod while allowing a gap for the air to escape from. If you dont do this, air will be trapped on the end of the fiberglass rod making for a weaker bond between the fiberglass and the stainless steel coupler. Once the coupler is on the rod and the air has escaped from between the coupler and fiberglass, give the coupler a few quarter turns, both left and right, in order to spread the JB Weld around the fiberglass rod. Allow 24 hours for the JB Weld to completely cure and set. When the couplers are all installed you are ready to use your extension.

Step-by-Step Installation Guide

Do you like instructions laid out in steps? We have you covered. Don’t have a Max-Gain Systems DIY Anchor system? Add capability to your existing anchor!

Follow these steps:
1.) Measure the diameter of your anchor rod
2.) Go to this link Make your current anchor modular
3.) select your rod diameter and Add to your Cart both a Male and Female Coupler
4.) You will need a fine toothed hacksaw OR an abrasive cut off wheel on an angle grinder or in a miter saw. Cut your current anchor about 6 inches below the handle (recommended location) or wherever you would like. (Be sure to make your cut straight)
5.) Use JB Weld Original Cold Weld Formula as shown in this Installation Guide
6.) Allow the epoxy to set and you have made your existing system into a modular system.

Once your system is modular, you can expand on it with our Extension Kits and our Paddle Kits.

Additional information

Shipping Weight N/A
Shipping Dimensions N/A
Extension Rod Diameter

3/4 inch OD, 1 inch OD


Black, White, Camo

Extension Rod Length

23.25 inches, 46.5 inches, 93 inches


You may also like…

  • Gaff Hook Pole DIY Kit GK-BASE (Black, 1 inch OD) 800x800 - Max-Gain Systems Inc

    Gaff Hook Pole DIY Kits

    SKU: GHK-BASESelect options
  • 4-in-1 Modular Paddle Kits

    SKU: PK-MODULARSelect options
  • PPM18F 18 foot long DIY Fiberglass Push Pole Modular Break Down Diagram - Max-Gain Systems, Inc.

    DIY Fiberglass Push Poles

    SKU: FPP-MOD-GRAY-16-FootAdd to cart
  • A SWA 8 ft 0.625 inch BLACK CLIP SQ 800x800 - Max-Gain Systems, Inc.

    DIY Shallow Water Anchor Part Kits

    SKU: SWASelect options

Customers who viewed this item also viewed…

  • Boating Push Poles DIY Fiberglass Push Poles

    DIY Fiberglass Push Poles

    SKU: FPP-BASESelect options
  • MRODCPL Male 1 inch ID and 3/4 inch ID Rod and Tube Couplings

    Stainless Steel Coupler Parts for Fiberglass Round Solid Rod and Tube

    SKU: MGS-RODCPLSelect options
  • T-Grips for Shallow Water Anchors - Max-Gain Systems, Inc.

    T-Grips for Shallow Water Anchors

    SKU: MGS-TGRIPSelect options
  • Stainless Steel Shallow Water Anchor Tips MGS-SSTIP 800x800 - Max-Gain Systems Inc

    Stainless Steel Shallow Water Anchor Tips

    SKU: MGS-SSTIPSelect options