N Male Solder Connector + UG-174 Reducer Combo for RG-174, RG-316, LMR-100A, and other 0.100 Inch OD Coax
Silver Plated Brass Body
Gold Plated Brass Center Pin
Detailed Product Information
This N Male Solder Connector + UG-174 Reducer Combo is one of several thousand RF products available from Max-Gain Systems, Inc.
This connector is made from a Solid Brass body that is precision machined and plated with Silver for superior performance and value. This N Male Solder Connector has a PTFE dielectric and a gold plated brass center pin. The N Male interface contains a gasket, for shock- / vibration- resistant and waterproof connections.
Compatible with Coaxial Cable Types: RG-174, RG-188, RG-188A/U, RG-316, RG-316/U Double Shield, LMR-100A, Belden 7805R, Belden 8216, Belden 83269, Belden 83284, Belden 84316, and other 0.100 Inch OD Coaxial cable.
See our entire line RF Connectors and Adapters:
We will begin by installing the Type N connector on a piece of RG-174. This process is the same for all the other types of cable that fit the Type N connector with a UG-174 reducer (0.100 OD Coax). These connectors fit on a wide range of coax types including: RG-174, RG-188, RG-188A/U, RG-316, RG-316/U Double Shield, LMR-100A, Belden 7805R, Belden 8216, Belden 83269, Belden 83284, Belden 84316, and other 0.100 Inch OD Coaxial cable.
First cut your cable to the desired length and place the reducer onto the coax. Strip the black jacket back approximately 1.02 inches. When the jacket is stripped cut the braid/foil back 0.315 of an inch from the fresh cut end.
Move the reducer up to the end of the black jacket and fold back the braid onto the reducer. If there are any strands of the braid, that make contact with the threads, trim them with small diagonal cutters. Finally, cut back the dielectric 0.433 of an inch from the fresh end down to the center conductor.
Main Body Install:
Put the main body on the end of the cable and grip it with a pair of pliers and begin screwing it to the right (clockwise) till you see the center conductor inside the solder hole of the center pin of the Type N connector itself.
FAQ #1: Why wont the center conductor go into the connector?
Answer 1: The center is bent off of center. Ensure the center conductor is perfectly straight before screwing the connector body onto the coax.
Answer 2: The tip of the center conductor was flattened by diagonal cutters when cutting the coax. To fix this, use a pair of pliers to round back out the tip of the center conductor.
Begin by positioning the solder hole, in the center pin, facing up. Turn on your soldering iron and allow sufficient time for the soldering iron tip to reach full operating temperature and clean the tip of the iron by wiping it with a damp sponge. Apply heat to the center pin of the Type N connector with your soldering iron by placing the “flat” of the iron underneath the pin. This allows maximum heat transfer to the pin and center conductor. Be sure the soldering iron is on the bottom side of the center pin. When the pin is heated, apply the solder to the tip of the center conductor. Allow sufficient solder to flow to seal the center conductor inside the center pin.
Once the center pin is sealed with solder, move the soldering iron to the holes on the body. Make sure to fill both of the holes with solder flush with the top of each hole. Once both holes of the connector are filled with solder let the connector cool down. When the connector is cool, screw on the other portion of the connector to complete your install.
When this is completed, as a final test, you should always check resistance from the center pin to the body with an ohmmeter in a low resistance scale. After verifying that there are no braid – to – center pin shorts on the other end of the coaxial cable, you should see infinite resistance (open). This completes your installation and the connector is ready for use!
See our entire line RF Connectors and Adapters:
About Max-Gain Systems, Inc.
Max-Gain Systems, Inc. carries a full line of in-series, between series, right angle, T-shaped, quick connect, handie-talkie (BLACK), pigtails (coaxial jumpers), etc… RF adapters. Our RF adapter lines are constantly expanding. We keep our RF connector and adapter lines in stock. We ship both retail and wholesale quantities. To become a dealer / wholesale user, contact us with your potential usage.
Max-Gain Systems, Inc. is the number one supplier of fiberglass round hollow tube, square tube and round solid rod to the antenna manufacturing industry. We produce millions of feet a year for hundreds of different industries including but not limited to: marine / boating, aeronautical, agriculture, construction, emergency services, etc…. We have the unique ability to sell one piece or even a semi-truck full. Feel free to prototype using our fiberglass tube and rod then contact us for a quote on a production run. At production run quantities we can cut to your desired lengths at no additional charge, and we can also perform several different fabrications (example: drilling holes in precise locations along a tube) to ensure your delivered material is ready for assembly. We have several accessory items designed for our fiberglass including but not limited to: couplers, telescoping clamps, ferrules, etc…