BNC male Crimp Connector for LMR-195, RG-58, and other 0.195 Inch OD Coax

$2.95$207.00

Quantity Discounts Available:
(Single Piece) Price: $2.95 each
(10 Pack) Price: $26.60 per pack Save 10%
(25 Pack) Price: $59.00 per pack Save 20%
(50 Pack) Price: $118.00 per pack Save 20%
(100 Pack) Price: $207.00 per pack Save 30%

 

Pack Quantity: These are sold in “pack” quantities. Choose the pack size you would like. The per unit price is based on this pack size.

BNC male Crimp Connector for LMR-195, RG-58, and other 0.195 Inch OD Coax

Silver Plated Brass Body
Gold Plated Brass Center Pin
Teflon Dielectric
“TGS”

Detailed Product Information
Description

This BNC male Crimp Connector is one of several thousand RF products available from Max-Gain Systems, Inc.

This connector is made from a Solid Brass body that is precision machined and plated with Silver for superior performance and value. This BNC male Crimp Connector has a PTFE dielectric and a gold plated brass center pin. The BNC male interface accepts the BNC female tabs or “bayonets” for quick and reliable connections and disconnections.

7005-BNC-58, 7005-58

Compatible with Coaxial Cable Types: RG-58, RG-58A/U, Belden 7807A, Belden 8219, Belden 8259, and Belden 9201 coaxial cable.

Installation Guide:

We will begin by installing the BNC crimp-on connector on a piece of coax. This process is the same for all the types of coaxial cable that fit this BNC crimp-on connector. These connectors fit on a wide range of coax types, including: LMR-195, LMR-200, RG-142, RG-142B/U, RG-141, RG-141A/U, RG-142A/U, RG-122/U, RG-400, RG-400/U, RG-58, RG-55, RG-55B/U, RG-55A/U, RG-58C/U, RG-223, RG-223/U, 0.195 Inch OD Coax.

Identify all connector parts (3 parts):

Each connector consists of one body assembly (plug), one rear ferrule (crimp sleeve), and one center pin (plug contact).

BNC male Crimp On for RG-58, LMR-195 7005-BNC-58 Installation Guide step 1 - Max-Gain Systems Inc

Coax Stripping:

First cut your coaxial cable to the desired length and then strip the black jacket back approximately 15mm (0.59”). When the jacket is stripped cut the braid/foil back 7.2mm (0.28”) from the fresh cut end. Finally, cut back the dielectric 3mm (0.12”) from the fresh end down to the center conductor. The braid needs to be cut back further than the dielectric to insure that none of the braid or foil is touching the center conductor which could cause a short.
Once the cable is prepped, make sure to put the ferrule (crimp sleeve) of the connector on the coaxial cable before you proceed.

BNC male Crimp On for RG-58, LMR-195 7005-BNC-58 Installation Guide step 2 - Max-Gain Systems Inc

Crimping and Soldering Install:

Place the center pin onto the conductor of the coaxial cable.

Soldering Guide (preferred):

This soldering guide is for soldering Max-Gain Systems, Inc. BNC crimp-on connectors. These are approximate measurements for our BNC crimp-on connectors, which adhere to industry standards for this type connector. If you choose to use this guide for connectors sold by others who do NOT adhere to these standards, the measurements could be off and result in a poor installation.

Now we begin soldering the center pin onto the center conductor of the coax.

Begin by applying heat to the center pin of the BNC connector with your soldering iron. Before proceeding, allow sufficient time for the soldering iron tip to reach full operating temperature and clean the tip of the iron by wiping it with a damp sponge. Place the soldering iron UNDER the center pin and, with the solder hole of the center pin facing up, apply the solder into the hole. The heat rises and heats up the pin faster. When the pin is heated the solder will start to flow into the pin. Allow sufficient solder to flow into the center pin to make a good connection, but not too much that it begins to leak out and potential start to melt the dielectric of the coax.

Crimping Guide:

Use the 0.052” hex die from your 7505-DIE-8X ratcheting crimper die to crimp the center pin above the small lip of the center pin right on top of the “solder hole”.

BNC male Crimp On for RG-58, LMR-195 7005-BNC-58 Installation Guide step 3 - Max-Gain Systems Inc

Die Only

P/N: 7505-DIE-8X

RG-58 & RG-59 Interchangeable Die for standard ratcheting crimper tools installed 7505-DIE-8X Close Up 800x800 - Max-Gain Systems Inc

Die and Tool Kit

P/N: 7505-HANDLE-8X

Crimp Tool and Die Set for RG-223, RG-59, LMR-240, RG-8X mini 8, and other 0.240 Inch OD Coax 7505-HANDLE-8X 800x800 - Max-Gain Systems Inc

Crimping The Ferrule:

Flare out the braid of the coax and slide the body assembly over the center pin and under the braid. Then seat the body assembly firmly onto the center contact. Arrange braid uniformly around the knurled portion of the body assembly. Slide the ferrule (crimp sleeve) forward and make sure it is in contact with the body assembly. Using the 0.213” hex die from the 7505-DIE-8X ratcheting crimper die to crimp the ferrule (crimp sleeve) right up next to the main body assembly. This crushes the metal sleeve around the braid and knurling to make it difficult for the connector to be removed. Trim any braid that extends out from crimp sleeve, against the body assembly, so not have any strays sticking out.

BNC male Crimp On for RG-58, LMR-195 7005-BNC-58 Installation Guide step 4 - Max-Gain Systems Inc

Final Testing:

When this is completed, as a final test, you should always check resistance from the center pin to the body with an ohmmeter in a low resistance scale. After verifying that there are no braid – to – center pin shorts on the other end of the coaxial cable, you should see infinite resistance (open). This completes your BNC male crimp-on connector installation, and the connector is ready for use!

See our entire line RF Connectors and Adapters:

RF Connectors

RF Connectors 300x300 - Max-Gain Systems Inc

RF Adapters

RF Adapters 300x300 - Max-Gain Systems Inc

About Max-Gain Systems, Inc.

Max-Gain Systems, Inc. carries a full line of in-series, between series, right angle, T-shaped, quick connect, handie-talkie (BLACK), pigtails (coaxial jumpers), etc… RF adapters. Our RF adapter lines are constantly expanding. We keep our RF connector and adapter lines in stock. We ship both retail and wholesale quantities. To become a dealer / wholesale user, contact us with your potential usage.

Max-Gain Systems, Inc. is the number one supplier of fiberglass round hollow tube, square tube and round solid rod to the antenna manufacturing industry. We produce millions of feet a year for hundreds of different industries including but not limited to: marine / boating, aeronautical, agriculture, construction, emergency services, etc…. We have the unique ability to sell one piece or even a semi-truck full. Feel free to prototype using our fiberglass tube and rod then contact us for a quote on a production run. At production run quantities we can cut to your desired lengths at no additional charge, and we can also perform several different fabrications (example: drilling holes in precise locations along a tube) to ensure your delivered material is ready for assembly. We have several accessory items designed for our fiberglass including but not limited to: couplers, telescoping clamps, ferrules, etc…

Additional information

Shipping Weight N/A
Shipping Dimensions N/A
Pack Quantity

Single Piece, 10 Pack, 25 Pack, 50 Pack, 100 Pack

Connection Type

, ,

Termination Type

Coax

Coax Type

, , , , , , , , ,

Gender

Male

Mount Method

None

Attachment Method

Connector Attribute

Body Style

Impedance

50 OHM

Body Material

Silver

Dielectric Insulator Material

PTFE

Pin Material

Gold

Material Designation

TGS

itemCondition

You may also like…