Pole Camera Mounts

$29.95$39.95

Mount your camera on top of our mast systems or our painter’s poles using our all Stainless Steel mount. It has the strength to give you the confidence that your equipment is safe while elevated.

Select below the Outer Diameter of the tube that you have to put the mount on.

For HD masts, choose 1″ (CM-1)
For STD and EXT masts, choose 3/4″ (CM-34)

Clear

Our Stainless Steel camera mount is the perfect solution to get the shot you want. You will have confidence that your equipment is safe while elevated with its all stainless steel construction.

This Stainless Steel camera mount has a 1/4 x 20 male threaded stud coming out of the top. The Stainless Steel base of the camera mount needs to be glued onto the pole that it is to be utilized on.

We recommend JB-Weld, 2 part epoxy, “Original Cold Weld Formula” adhesive to apply this camera mount onto your pole. Simply spread your adhesive around the outside of the tube and slip on the camera mount. Allow adequate time for the adhesive to setup and you are ready to begin getting those shots!

Assembly

The best adhesive to use to attach the camera mount to then ends of the fiberglass tubing (or any tube or rod that is smaller than the ID these will accept) is JB Weld, Original Cold-Weld Formula. Mix the epoxy then apply a generous layer around the end of the tubing or rod. Slide on the coupling and allow time to set.

JB Weld Original Cold-Weld Formula, Steel Reinforced 2 part epoxy

One additional method could be used and that is the “pinning” method. Place the part on the end of the tube or rod. With the part “seated” drill a 9/64″ hole through the overlap area. Insert a #6:32 machine screw of the corresponding length to the largest diameter piece being drilled. An illustration of this method is below:

Part Assembly Pinning Method

For Pinning through:

  • 0.75 inch OD Parts, use #6:32 round-head machine screws, 1 inches long.
  • 1 inch OD Parts, use #6:32 round-head machine screws, 1.25 inches long.

Have a ball mount you would like to use? Get a 1/4 x 20 to 3/8 x 16 adapter

MGS-1420F-3816F-ADP 14x20 to 38x16 adapter - Max-Gain Systems, Inc.MGS-1420F-3816F-FL-ADP 14x20 to 38x16 adapter with integral flange and cork insert - Max-Gain Systems, Inc.

Need an extendable pole to get elevated?

2-Piece Painter Poles

ImageNameMaximum Usable LengthLength When SleevedLength of TubesWeight per Linear Foot (lb/ft)PriceBuy
2 piece painters pole - Max-Gain Systems, Inc.
7.7 feet Adjustable 2-Piece Painter's Poles7 feet 7 inches4 feet 3 inches4 feet2.3 Lbs$24.95$64.80
2 piece painters pole - Max-Gain Systems, Inc.
3.7 feet Adjustable 2-Piece Painter's Poles3 feet 8 inches2 feet 3 inches2 feet1.3 Lbs$19.45$59.30
2 piece painters pole - Max-Gain Systems, Inc.
15.1 feet Adjustable 2-Piece Painter's Poles15 feet 1 inch8 feet 3 inches8 feet4.3 Lbs$36.45$76.30
2 piece painters pole - Max-Gain Systems, Inc.
11.6 feet Adjustable 2-Piece Painter's Poles11 feet 5 inches6 feet 3 inches6 feet3 Lbs$32.95$72.80

3-Piece Painter Poles

ImageNameMaximum Usable LengthLength When SleevedLength of TubesWeight per Linear Foot (lb/ft)PriceBuy
3 piece painters pole - Max-Gain Systems, Inc.
5.7 feet Adjustable 3-Piece Painter's Poles5 feet 7 inches2 feet 7 inches2 feet2.1 Lbs$36.45$76.30
3 piece painters pole - Max-Gain Systems, Inc.
22.1 feet 3-Piece Painter's Poles22 feet 1 inch8 feet 6 inches8 feet7.5 Lbs$69.75$109.60
3 piece painters pole - Max-Gain Systems, Inc.
16.9 feet Adjustable 3-Piece Painter's Poles16 feet 10 inches6 feet 6 inches6 feet5.3 Lbs$56.95$96.80
3 piece painters pole - Max-Gain Systems, Inc.
11.2 feet Adjustable 3-Piece Painter's Poles11 feet 3 inches4 feet 6 inches4 feet3.8 Lbs$47.75$87.60

About Max-Gain Systems, Inc.

Max-Gain Systems, Inc. carries a full line of in-series, between series, right angle, T-shaped, quick connect, handie-talkie (BLACK), pigtails (coaxial jumpers), etc… RF adapters. Our RF adapter lines are constantly expanding. We keep our RF connector and adapter lines in stock. We ship both retail and wholesale quantities. To become a dealer / wholesale user, contact us with your potential usage.

Max-Gain Systems, Inc. is the number one supplier of fiberglass round hollow tube, square tube and round solid rod to the antenna manufacturing industry. We produce millions of feet a year for hundreds of different industries. Including but not limited to:  marine / boating, aeronautical, agriculture, construction, emergency services, etc….  We have the unique ability to sell one piece or even a semi-truck full. Feel free to prototype using our fiberglass tube and rod then contact us for a quote on a production run. At production run quantities we can cut to your desired lengths at no additional charge. We can also perform several different fabrications (example: drilling holes in precise locations along a tube) to ensure your delivered material is ready for assembly. We have several accessory items designed for our fiberglass including but not limited to: couplers, telescoping clamps, ferrules, etc…

Additional information

Shipping WeightN/A
Shipping DimensionsN/A
Fits On

3/4 inch OD, 1 inch OD

itemCondition

You may also like…