Type N female Crimp Connector for LMR-600, RG-217/U, and other 0.590 Inch OD Coax

$10.95$767.00

Quantity Discounts Available:
(Single Piece) Price: $10.95 each
(10 Pack) Price: $98.60 per pack Save 10%
(25 Pack) Price: $219.00 per pack Save 20%
(50 Pack) Price: $438.00 per pack Save 20%
(100 Pack) Price: $767.00 per pack Save 30%

Pack Quantity: These are sold in “pack” quantities. Choose the pack size you would like. The per unit price is based on this pack size.

Type N Female Crimp Connector for LMR-600, RG-217/U and other 0.590 Inch OD Coax

Silver Plated Brass Body
Gold Plated Brass Center Pin
PTFE Dielectric
“TGS”

Detailed Product Information
Description

This Type N Female Crimp Connector is one of several thousand RF products available from Max-Gain Systems, Inc.

This connector is made from a Solid Brass body that is precision machined and plated with Silver for superior performance and value. This N Female Crimp Connector has a PTFE dielectric and a gold plated brass center pin. The N Female interface accepts a N male which contains a gasket, for shock- / vibration- resistant and waterproof connections.

7306-N-600, 7306-600

Compatible with Coaxial Cable Types: LMR-600 and RG-217/U coaxial cable.

Installation Guide:

We will begin by installing the Type N female connector on a piece of LMR-600. This process is the same for all the other types of cable with an outer jacket OD of 0.590. These connectors fit on a wide range of coax types including, but not limited to: RG-217/U, LMR-600, and other 0.59 inch OD coax.

Identify all connector parts (3 parts):

Each connector consists of one body assembly (jack), one rear ferrule (crimp sleeve), and one center pin (jack contact).

Type N female Crimp On for LMR-600, and other 0.590 Inch OD Coax 7306-N-600 v2 - Max-Gain Systems Inc

Coax Stripping:

First cut your cable to the desired length and then strip the black jacket back approximately 0.55 inches. When the jacket is stripped cut the braid/foil back 0.225 inches from the fresh cut end. Finally, cut back the dielectric 0.16 inches from the fresh end down to the center conductor. The braid needs to be cut back further than the dielectric to insure that none of the braid or foil is touching the center conductor which could cause a short.
Note: Do not nick the braid, dielectric, and center conductor if at all possible. Tinning of the center conductor is not necessary if contact is to be crimped. For solder method, tin the center conductor if the center is stranded. twist the center conductor very tightly prior to tinning.

Type N female Crimp On for LMR-600, and other 0.59 Inch OD Coax 7306-N-600 installation guide drawings step 1 - Max-Gain Systems Inc

Installation Method Selection:

Slide the outer ferrule onto the coax as shown below. Flare the braid slightly to allow insertion of the connector main body. Important: Do not comb out braid.
Place the center contact on the center conductor of the coax so that it butts against the cable dielectric. The center conductor should be visible through the solder / inspection hole of the contact. Solder contact in place as follows:

Crimp-on the Ferrule

Use the 7505-HANDLE-600 crimp handle for the ferrule. (DO NOT CRIMP / CRUSH THE CENTER PIN)

LMR-600 Connector Crimp Tool 7505-HANDLE-600 1498x537 - Max-Gain Systems Inc

Solder the Pin

Make sure the solder hole is facing up. Touch the soldering iron to the underside of the center pin directly under the solder hole. Touch the solder to the center conductor through the solder hole on the center pin. Allow the heat from the metal to melt the solder so that it wicks into the center pin. Once the solder melts it only takes a tiny amount of solder to make the connection. Do not allow the solder to pool over the solder hole. The outside of the center pin should be free of obstructions for insertion. Do not over heat the center pin which could cause swelling of the dielectric of the coax.

Type N female Crimp On for LMR-600, and other 0.59 Inch OD Coax 7306-N-600 installation guide drawings step 2 - Max-Gain Systems Inc

Main Body Install:

Install the cable assembly with the center pin already affixed, into the main body of the connector. The knurled portion of the main body slides under the braid of the coax. Push the cable assembly into the main body until the center pin snaps into place in the dielectric of the connector.
Slide the ferrule (placed on the coax at the beginning of Step 2) over the braid and completely up against the connector body. Using the 0.590 hex of the 7505-HANDLE-600 crimp handle, crimp the ferrule at the location shown in the picture below (on the ferrule, but right up against the main body of the connector).

Type N female Crimp On for LMR-600, and other 0.59 Inch OD Coax 7306-N-600 installation guide drawings step 3 - Max-Gain Systems Inc

Final Testing:

When this is completed, as a final test, you should always check resistance from the center pin to the body with an ohmmeter in a low resistance scale. After verifying that there are no braid – to – center pin shorts on the other end of the coaxial cable, you should see infinite resistance (open).

See our entire line RF Connectors and Adapters:

RF Connectors

RF Connectors 300x300 - Max-Gain Systems Inc

RF Adapters

RF Adapters 300x300 - Max-Gain Systems Inc

About Max-Gain Systems, Inc.

Max-Gain Systems, Inc. carries a full line of in-series, between series, right angle, T-shaped, quick connect, handie-talkie (BLACK), pigtails (coaxial jumpers), etc… RF adapters. Our RF adapter lines are constantly expanding. We keep our RF connector and adapter lines in stock. We ship both retail and wholesale quantities. To become a dealer / wholesale user, contact us with your potential usage.

Max-Gain Systems, Inc. is the number one supplier of fiberglass round hollow tube, square tube and round solid rod to the antenna manufacturing industry. We produce millions of feet a year for hundreds of different industries including but not limited to: marine / boating, aeronautical, agriculture, construction, emergency services, etc…. We have the unique ability to sell one piece or even a semi-truck full. Feel free to prototype using our fiberglass tube and rod then contact us for a quote on a production run. At production run quantities we can cut to your desired lengths at no additional charge, and we can also perform several different fabrications (example: drilling holes in precise locations along a tube) to ensure your delivered material is ready for assembly. We have several accessory items designed for our fiberglass including but not limited to: couplers, telescoping clamps, ferrules, etc…

Additional information

Shipping Weight N/A
Shipping Dimensions N/A
Pack Quantity

Single Piece, 10 Pack, 25 Pack, 50 Pack, 100 Pack

Connection Type

, ,

Termination Type

Coax

Coax Type

, , , ,

Gender

Female

Mount Method

None

Attachment Method

Connector Attribute

Body Style

Impedance

50 OHM

Body Material

Silver

Dielectric Insulator Material

PTFE

Pin Material

Gold

Material Designation

TGS

itemCondition

You may also like…

  • 7330-TGS N male to UHF female DGN Adapter - Max-Gain Systems, Inc.

    Type N male to UHF female Adapter (Best)

    $10.95$767.00
    SKU: 7330-TGS-A2Select options
  • Type N male Crimp On for LMR-600, and other 0.590 Inch OD Coax 7305-N-600 800x800 - Max-Gain Systems Inc

    Type N male Crimp Connector for LMR-600, RG-217/U, and other 0.590 Inch OD Coax

    $10.95$767.00
    SKU: 7305-N-600Select options
  • UHF male Crimp On for LMR-600, and other 0.590 Inch OD Coax 7505-UHF-600 800x800 - Max-Gain Systems Inc

    UHF male Crimp Connector for LMR-600, RG-217/U, and other 0.590 Inch OD Coax

    $12.95$907.00
    SKU: 7505-UHF-600Select options
  • UHF female Crimp On for LMR-600, and other 0.590 Inch OD Coax 7506-UHF-600 800x800 - Max-Gain Systems Inc

    UHF female Crimp Connector for LMR-600, RG-217/U, and other 0.590 Inch OD Coax

    $12.95$907.00
    SKU: 7506-UHF-600Select options

Customers who viewed this item also viewed…

  • Greenstone VHC-1 Vacuum Relay 800x800 - Max-Gain Systems Inc

    3.5 kV, 5 kV Peak, SPDT, 25 Amps, VHC-1 – NEW Vacuum Relay

    $119.95
    SKU: VHC-1Select options
  • 38 feet Heavy Duty Fiberglass Push-up Mast MK-6-HD 800x800 - Max-Gain Systems, Inc.

    38 feet Heavy Duty Fiberglass Push-up Mast MK-6-HD

    $329.95$445.95
    SKU: MK-6-HDSelect options
  • RT-1 1 inch OD Round Hollow Tube 800x800 - Max-Gain Systems, Inc.

    1″ OD, 3/4″ ID Fiberglass Round Tube

    $3.79$29.95
    SKU: RT-1Select options
  • PL-259 UHF male Solder On for LMR-400, RG-213, RG-8 7500-UHF 800x800 - Max-Gain Systems Inc

    PL-259, UHF male Solder Connector for RG-8, RG-11, RG-83, RG-213, RG-393, LMR-400, and other 0.405 Inch OD Coax

    $2.25$158.00
    SKU: 7500-UHFSelect options